3003 Aluminum Coils

Short Description:


  • Aluminum Alloy: A1050,A1060,A1070,A1100,A3003,A3004,A3105,A5052, A5005,A5083,A5754,A6061,A6082,A6063,A8011
  • Property: Anti-corrosion,heat resistant
  • Surface: Mill Finish,No Stains,Without Rough Selvedge
  • Production Process: Cold Rolled,Hot Rolled
  • Internal Diameter: 305mm,405mm,505mm or per request
  • Temper: O,H18,H24,H32,H112 Etc;T4,T5,T6,T651 Etc
  • Thickness: 0.2mm - 200mm
  • Width: 600mm - 2000mm
  • Coil Weight: 2-4 tons
  • Standards: ASTMB209,EN573,EN485
  • Description

    Specification

    Standards

    Process

    Packing

    3003 aluminum coils belong to a kind of AL-Mn alloy which is approximately 10% stronger than alloy 1100. 3003 aluminum sheets are non-heat treatable, so the mechanical property is improved by cold processing: it has high plasticity in annealed condition, good plasticity when semi-cold hardening, while low plasticity during cold hardening. It has good corrosion resistance, excellent weldability, but poor machinability. It is mainly used on low load parts working in liquid or gas and require high formability and weldability, such as oil tank, gasoline or lubricate pipe, liquid container, and other low load parts made by deep drawing. Wire rods are used to make rivets.

    Application:

    With the excellent rust proof property, 3003 aluminum sheets/coils are appropriate to be used in humid environments like refrigerators or air conditioners ducts, mechanical parts, or external packing.

    3003 aluminum coils are also widely applied to ships/vessels, vehicles, automobile and inserter welding assemblies, fireproof pressure vessels, refrigeration equipment, television tower, drilling equipment, transport and communication facilities, missile elements, plate armors and so on.

    Performance

    1) Good corrosion resistance and moderate strength.;

    2) Excellent weldability, formability, and machinability.

     


  • Previous:
  • Next:

  • PRODUCTNAME ALLOYS NUMBER TEMPER THICKNESS(MM) WIDTH(MM) LENGTH(MM) APPLICATION
    3003 Aluminum           Coil  3003 O,H12,H14,H16H18,H19,H22,H24,H26,H28,H32,H34
    H36,H38
     0.2-7.0 20-2200 600-6000 Bottle cap, beverage bottle cap, cosmetic cap and so on

    Mechanical Properties

    Mechanical property requirements for annealed product (O temper) as specified in ASTM B209 and ASME SB209

    Thickness (inch) Yield Strength Min. (ksi)

    Tensile Strength (ksi)

    Elongation (%)
    Min.

    Bend Diameter Factor,N

    Min. Max.
    0.006 – 0.019 5.0 14.0 19.0 14 0
    0.008 – 0.012 5.0 14.0 19.0 18 0
    0.013 – 0.031 5.0 14.0 19.0 20 0
    0.032 – 0.050 5.0 14.0 19.0 23 0
    0.051 – 0.249 5.0 14.0 19.0 25 0
    0.250 – 3.00 5.0 14.0 19.0 23 -

    Mechanical property requirements for strain hardened H12 temper (¼ hard) as specified in ASTM B209 and ASME SB209

    Thickness (inch) Yield Strength Min. (ksi)

    Tensile Strength (ksi)

    Elongation (%)
    Min.

    Bend Diameter Factor,N

    Min. Max.
    0.017 – 0.019 12.0 17.0 23.0 3 0
    0.020 – 0.031 12.0 17.0 23.0 4 0
    0.032 – 0.050 12.0 17.0 23.0 5 0
    0.051 – 0.113 12.0 17.0 23.0 6 0
    0.114 – 0.161 12.0 17.0 23.0 7 0
    0.162 – 0.249 12.0 17.0 23.0 8 0
    0.250 – 0.499 12.0 17.0 23.0 9 -
    0.500 – 2.000 12.0 17.0 23.0 10 -

    Mechanical property requirements for strain hardened H14 temper (½ hard) as specified in ASTM B209 and ASME SB209

    Thickness (inch) Yield Strength Min. (ksi)

    Tensile Strength (ksi)

    Elongation (%)
    Min.

    Bend Diameter Factor,N

    Min. Max.
    0.009 – 0.012 17.0 20.0 26.0 1 0
    0.013 – 0.019 17.0 20.0 26.0 2 0
    0.020 – 0.031 17.0 20.0 26.0 3 0
    0.032 – 0.050 17.0 20.0 26.0 4 0
    0.051 – 0.113 17.0 20.0 26.0 5 0
    0.114 – 0.161 17.0 20.0 26.0 6 2
    0.162 – 0.249 17.0 20.0 26.0 7 2
    0.250 – 0.499 17.0 20.0 26.0 8 -
    0.500 – 1.000 17.0 20.0 26.0 10 -

    Physical Properties
    Physical properties for Alloy 3003

    Property 3003 Data
    Density, lb/in3 0.099
    Modulus of Elasticity, psi 10.0 x 106
    Coefficient of Thermal Expansion, 68-212˚F, /˚F 12.9 x 10-6
    Thermal Conductivity, Btu/ft hr ˚F 112
    Specific Heat, Btu/lb ˚F 0.213
    Electrical Resistivity, Microohm-in 1.374

    CHEMICAL COMPOSITION LIMITS (%)

    Si
    Silicon

    Fe
    Iron

    Cu
    Copper

    Mn
    Manganese

    Mg
    Magnesium

    Cr
    Chromium

    Ni
    Nickel

    Zn
    Zinc

    Ti
    Titanium

    Others
    Each

    Total
     

    Total
    Aluminum Min

    0.6

    0.7

    0.05 – 0.2

    1.0 – 1.50

    -

    -

    -

    0.1

    -

     0.05

    0.15

    Remainder

     

    Chemical composition is percent maximum unless shown as a range or a minimum.

    Source: Aluminum Standards and Data The Aluminum Association, Inc.

    Information presented as a guide for reference purposes only and is not intended to be used for product design or application.

    ASTMB209EN573EN485

    ASTMB209–This specification covers aluminum and aluminum alloy flat sheet,coiled sheet, and plate in various alloys.

    BS EN 573–This specification covers aluminium and aluminium alloys–chemical composition and form of products.

    BS EN 485–This specification sets out the mechanical properties of wrought aluminium amd wrought aluminium alloy sheet, strip and plate for general engineering applications

     

    process of coil

    Packing Details : Standard export package.

    Aluminium Sheet of packaging meet the export standard. Plastic film and brown paper can be covered at customers’ need. wooden case or wooden pallet is adopted to protect products from damage during the delivery.

    Packing : Export wooden pallets,  craft paper, anti-blushing agent.
    The inner size of container is below:
    20ft GP: 5.8m(length) x 2.13m(width) x 2.18m(high) about 24-26CBM,23MTS
    40ft GP: 11.8m(length) x 2.13m(width) x 2.18m(high) about 54CBM,27MTS
    40ft HG: 11.8m(length) x 2.13m(width) x 2.72m(high) about 68CBM,27MTS

    Alminium coils packing