Price List

Hunan Great Steel Pipe Co., Ltd
plastic coated steel pipe,carbon steel pipe supplier,carbon steel pipe manufacturer

How to Detect the Quality of Spiral Steel Pipe

Date: 2023-06-20
How to Detect the Quality of Spiral Steel Pipe Spiral pipe factory should be done before the mechanical performance test and flattening test, and flaring test, and to achieve the standard requirements. Spiral steel pipe quality inspection method is as follows: 1, From the face of it, that is visual inspection. Visual inspection of welded joints is a simple procedure but widely used test method is an important part of product testing, the main defects and deviations are found on the surface of the weld size. Usually by the naked eye, with the standard model, gauge and test tools such as a magnifying glass. If the weld surface defects, weld defects there may be internal. 2, Physical test methods: physical test method is to use some physical phenomena assay or test method. Or within the workpiece material defect inspection, and are generally used NDT methods. NDT ultrasonic flaw detection, radiation detection, penetration testing, magnetic testing and so on. 3, Pressure vessels strength test: pressure vessels, in addition to tightness test, but also the strength test. There are common test of two hydraulic test and air pressure. They can be tested in working under pressure vessels and piping welds compactness. Hydrostatic pressure test is more sensitive than the test speed and, at the same time after the test products do not waste water treatment, drainage problems for the product is particularly applicable. But the risk is greater than the test pressure test. When tested, it must comply with the appropriate safety measures to prevent accidents during the test. 4, Compact test: liquid or gas storage vessel welding, which is not dense weld defects, such as penetrating cracks, pores, slag, incomplete penetration loose tissue and the like, can be used to find the density test. Compactness test methods are: kerosene test, carrying water testing, water will test. 5, The hydrostatic test should be done each pipe hydrostatic test without leakage, pressure test press Calculate P = 2ST / D where S- hydrostatic test stress test Mpa, hydrostatic test stress test according to the corresponding steel standard specifies the minimum degree of yield (Q235 is 235Mpa) 60% of the selection. Regulators time: D <508 test pressure holding time less than 5 seconds; D≥508 test pressure holding time less than 10 seconds 4, non-destructive testing of steel welding seam, strip end weld and circumferential joints should X-ray or ultrasonic inspection. For ordinary combustible fluid transport spiral steel to weld should be 100% SX-ray or ultrasound test, used for water, sewage, air, heating steam and other general transmission fluid with spiral weld steel pipe should be X-rays or ultrasonic inspection checks (20%). The spiral steel pipe quality test results, spiral pipe usually divided into three categories: Qualified, rework and scrap. Qualified means the quality and appearance of the intrinsic quality to meet the standards or technical delivery and acceptance conditions spiral steel pipe; rework refers to the quality and appearance of the intrinsic quality does not fully comply with the acceptance criteria and strip body, but allow the repair after repair can meet the standards and acceptance conditions spiral pipe; waste refers to substandard quality and appearance of the intrinsic quality of spiral steel still not up to standard and acceptance conditions do not allow repair or rework later. Post time: Jun-20-2023

Latest news list

  • FBE steel pipe field joint coating,FBE pipe welding protection,field joint coating,FBE coating repair,FBE field joint inspection
    FBE (fusion-bonded epoxy) coating provides external corrosion protection for steel pipes used in pipeline projects,However,during pipeline construction,the coating near pipe ends must be protected while individual pipe sections are joined by welding,The exposed joint area then requires a suitable field joint coating system,If this work is not properly controlled,damage or poor bonding at the joint can compromise the continuity of the pipeline's corrosion protection,Protecting the factory coating and applying the correct field joint system are therefore important parts of pipeline construction,
  • how to choose FBE coated steel pipe,FBE pipe selection,FBE coated pipeline requirements,FBE coated steel pipe size,FBE coated steel pipe purchase
    Selecting FBE coated steel pipes for a pipeline project involves more than specifying pipe diameter,wall thickness and coating thickness,Buyers must consider the base pipe,coating system,operating environment,installation conditions and inspection requirements as one coordinated package,A well-defined purchase specification helps prevent material mismatches,coating defects and documentation gaps before production begins,The following points provide a practical checklist for engineers,EPC contractors and procurement teams,
  • FBE coating and cathodic protection,FBE coated steel pipe,external pipeline corrosion control,cathodic protection monitoring,FBE coating disbondment
    Buried steel pipelines are exposed to moisture,soil chemicals and other environmental conditions that can cause external corrosion,To reduce this risk,pipeline projects commonly combine external fusion-bonded epoxy (FBE) coating with cathodic protection (CP),Although both methods help protect steel against corrosion,they work in different ways,FBE coating provides a physical barrier between the pipe surface and its surroundings,while cathodic protection uses an electrochemical process to reduce corrosion at exposed areas,Their effectiveness depends on proper design,installation,inspection and long-term monitoring,
  • FBE coated steel pipe quality control,FBE coating inspection,FBE coating thickness measurement,FBE pipe inspection,FBE coating quality control
    The quality of an FBE (Fusion Bonded Epoxy) coated steel pipe cannot be judged by its appearance alone,A smooth coating surface does not necessarily mean that the coating has achieved the required thickness,adhesion,or curing condition,For pipeline applications,quality control starts with the incoming bare steel pipe and continues through surface preparation,coating application,curing,and final inspection,Each stage should follow an approved procedure and the requirements specified for the project,A documented inspection process also allows buyers to verify that the supplied pipes meet the agreed technical requirements,
  • FBE coated steel pipes for buried pipelines,buried pipeline corrosion protection,FBE coated steel pipe installation
    FBE (Fusion Bonded Epoxy) coating is widely used to protect steel pipes against external corrosion in buried pipeline systems,It forms a protective barrier between the steel surface and the surrounding soil,However,coating performance depends on more than the quality of the factory-applied layer,Soil conditions,transportation,installation,field joint protection and cathodic protection all affect the long-term integrity of a buried pipeline,A reliable protection strategy should address these factors before the pipe is placed underground,

Find what you need ?

close
We use cookies and other tracking technologies to improve your browsing experience on our website, to show you personalized content and targeted ads, to analyze our website traffic, and to understand where our visitors are coming from.